Fluke 789/773 BU - 789 and 773 Bundle Package

Fluke 789 ProcessMeter

Now compatible with Fluke Connect™ App

The Fluke 789 ProcessMeter is the ultimate troubleshooting tool for electricians and instrumentation professionals, combining the functionality of a loop calibrator with the power of a digital multimeter. By equipping the 789 with a temperature measurement module and the wireless data logging capabilities of Fluke Connect™ with ShareLive™ video call (sold separately), process technicians can now do a lot more while carrying a lot less. And with its built-in, selectable 250 ohm HART® resistor, it eliminates the need to carry a separate resistor with you.

Fluke 773 Milliamp Process Clamp Meter

Need more hours in your day?

Save time by NOT breaking the loop on 4-20 mA signal measurements.

Are you spending time:

• Taking mA measurements by removing a wire and breaking the loop
• Calling the control room to isolate a loop
• Testing analog input/output on a console
• Troubleshooting devices with mA inputs and outputs
• Repairing intermittent or erratic 4-20 mA loops
• Going back to the shop to get extra tools

If you need more time in your busy day take a good look at the Fluke 773 mA Clamp Meters. It’s designed to save you time, and money, by eliminating time wasting activities. Now you can troubleshoot and repair 4-20 mA loops without breaking the loop or bringing down the system.

Here are some specific ways the Fluke 773 Clamp Meters will help you:

Milliamp Clamp Features

Measure mA signals for PLC and control system analog I/O without breaking the loop

• Measures low level dc current
• Correlate process indication with real physical value

Measure output signals from transmitters without breaking the loop

• Maintain and troubleshoot process and automation equipment without breaking the loop
• No disruption to the process

Detachable clamp with extension cable

• Measurements in tight locations
• Enables measurements in difficult situations

Measurement Spotlight

• Illuminates hard to see wires in dark enclosures
• Measurement process is easier and quicker

Measure up to 99.9 mA range non-contact

• Wide range of measurements
• Measures 10 to 50 mA signals in older control systems

Automatic power off

• After 15 minutes and 2 minute automatic off for backlight and spotlight
• Saves battery life

Features of the Fluke 789:

• 24 V Loop power supply
• Very large dual display
• Enhanced backlight with 2 brightness settings
• 1200 ohm drive capability on mA source
• HART mode setting with loop power and a built-in 250 ohm resistor
• 0% and 100% buttons to toggle between 4 and 20 mA sourcing for a quick span check
• Externally accessible fuses for easy replacement
• Infrared-port to process data in FlukeView Forms (V2.1) software

Fluke 789 features that are also included in the Fluke 787:

• Precision 1000 V, 440 mA True-RMS digital multimeter
• 0.1% dc voltage accuracy
• 0.05% dc current accuracy
• Frequency measurement to 20 kHz
• Min/Max/Average/Hold/Relative modes
• Diode Test and Continuity Beeper
• Simultaneous mA and % of scale readout
• 20 mA DC current source / loop calibrator / simulator
• Manual Step (100%, 25%, Coarse, Fine) plus Auto Step and Auto Ramp
• Externally accessible battery for easy battery changes

Safety conformance

Meets 1000 Volt EN61010-1 CAT III standards and 600 Volt EN61010-1 CAT IV standards.

The 773 mA Clamp Meter features:

• Best in class 0.2% accuracy
• 0.01 mA resolution and sensitivity
• Measure 4 to 20 mA signals without “breaking the loop”
• Measure mA signals for PLC and control system analog I/O
• Dual backlit display with both mA measurement and percent of 4 to 20 mA span
• Measurement Spotlight illuminates hard to see wires in dark enclosures
• Detachable clamp with extension cable for measurements in tight locations
• Measure 10 to 50 mA signals in older control systems using the 99.9 mA range
• Automatically change the 4 to 20 mA output for remote testing
• Power saving features, auto-off, backlight timeout extend battery life
• Hold function captures and displays changing measurements
• Measure 4 to 20 mA signals with in-circuit measurement
• Simultaneous mA in-circuit measurement with 24V loop power for powering and testing transmitters
• Source 4 to 20 mA signals for testing control system I/O or I/Ps
• mA output linear ramp or 25% step output
• Automatically change the 4 to 20 mA output for remote testing
• DC voltage measurement to verify 24V power supplies or voltage I/O signals
• Source DC voltage to test input devices that accept a 1-5V or 0 to 10V signals
• Scaled mA output provides a continuous mA signal that corresponds to the 4 to 20 mA signal measured by the mA clamp
• Enables milliamp signal logging to a separate logging device without breaking the loop
• Output mA signal enables a logging DMM or other device to record the 4- to 20 mA signal without breaking the loop
• mA in/out: simultaneously measure the mA signal with the clamp and source a mA signal
• Apply a mA input signal to a device and measure its’ 4-20 mA output on devices such as valves or mA isolators
• Voltage output linear ramp or 25% step output
• Automatically change the voltage output for remote testing

Do you have a 789 and 773 Bundle Package that needs to be calibrated?

We offer standard traceable calibration and ISO 17025 accredited calibration services.