Your Cart
(empty)
0
Tradeport Electronics
measurement is our business
Cart : (empty)

Fluke 884X-1G - USB Memory 1 GB

Used on the 8846A only Plugs into USB device host port on the 8846A front panel Fully compliant with Universal Serial Bus Specification v2.0 Dual LED indicates power and busy stat

by quote only

Used on the 8846A only Plugs into USB device host port on the 8846A front panel Fully co...

View Product

Fluke 8845A-TPIT - Test Probe IC Tip Set (red and black)

One pair (red and black),Snaps onto DMM probes with .080 in (2 mm) O.D. Tips, Designed to IEC 1010 standard, Pin tip jack at the adapter end is recessed for added insulation protection, Adapter allows easy access to leads of through-hole IC’s, Insulation

by quote only

One pair (red and black),Snaps onto DMM probes with .080 in (2 mm) O.D. Tips, Designed to ...

View Product

Fluke 8845A-EFPT - Extended Fine Point Tip Adapter Set (red and black)

One pair (red and black, Snaps onto DMM probes with .080 in (2 mm) O.D. Tips, Designed to IEC 1010 standard, Adapter allows access to hard-to-reach test points, Tips are insulated to the point to prevent shorting of adjacent components

by quote only

One pair (red and black, Snaps onto DMM probes with .080 in (2 mm) O.D. Tips, Designed to ...

View Product

Fluke 87-RETROFIT - Kit for 83, 85, 87-3, Meters

Refurbish your Fluke 80 Series meters

by quote only

Refurbish your Fluke 80 Series meters...

View Product

Fluke 85RF-II - 85RF High Frequency Probe (500MHz)

The 85RF High Frequency Probe is designed to convert a DC voltmeter with a input impedance of 10M ohms into a high frequency (100kHz to 500Mhz) RF voltmeter. Conversion from AC to DC is accomplished on a one-to-one basis includes a range of 0.25 to 30V rms. The probe's DC output is calibrated to be equivalent to the rms value of a sine wave input.

by quote only

The 85RF High Frequency Probe is designed to convert a DC voltmeter with a input impedance...

View Product

Fluke 80TK - Thermocouple Module

Converts a DMM to a thermometer, for use with type-K thermocouples in low voltage applications (below 24 V AC, 60 V DC).

by quote only

Converts a DMM to a thermometer, for use with type-K thermocouples in low voltage applicat...

View Product

Fluke 80T-150UA - Universal Temperature Probe

Compatible with Fluke DMMs High accuracy and fast reading for low voltage (below 24 V AC, 60 V DC) applications Measurement range: -50 to 150°C Output: 1 mV/°C or 1 mV/°F (switchable) One year warranty

by quote only

Compatible with Fluke DMMs High accuracy and fast reading for low voltage (below 24 V AC,...

View Product

Fluke 80PT-EXT - Extension Wire Kit

Extending and repairing T-type thermocouple wires Kit includes 3 meters of thermocouple wire and 1 pair of male/female mini-connectors Maximum continuous exposure temperature: 260ºC 80PT-EXT is designed for T-type thermometers One year warranty

by quote only

Extending and repairing T-type thermocouple wires Kit includes 3 meters of thermocouple w...

View Product

Fluke 80PT-25 - SureGrip Piercing Temperature Probe

Operates with T-type thermometers Measurement range: -196 to 350°C

by quote only

Operates with T-type thermometers Measurement range: -196 to 350°C...

View Product

Fluke 80PR-60 - RTD Temperature Probe for and

The 80PR 60 probe expands the utility of your RTD non-contact infrared thermometer by allowing you to take contact temperature readings. You can make contact and non-contact readings at the same time because your RTD infrared thermometer displays the results of both. Just plug the temperature probe into the RTD jack, position the probe tip at or below the surface of your target, and start reading temperatures. (Refer to thermometer user manual for details.)

by quote only

The 80PR 60 probe expands the utility of your RTD non-contact infrared thermometer by allo...

View Product